Do you find yourself trying to locate details on Installing A Bathtub?
Installing a bath tub isn't precisely rocket science, yet it does need solid plumbing, woodworking, and also often, tiling skills. Changing an old tub with a new one is additionally a moderately hard job. If the old tub is conveniently easily accessible, the project can relocate rapidly; if you need to open up a wall surface to remove the old bathtub as well as position the brand-new bathtub, the job is much harder. In either instance, the job is within a home handyman's abilities, although you will require a helper to move out the old bathtub and embeded in the new one. See to it you have certified yourself for the task and fit attempting it. Instead of working with a specialist to take over a halfway-completed project, it is much better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This write-up will aid you install a brand-new tub in your bathroom if you have currently purchased a brand-new tub as well as do not require to alter the setup of your previous water supply pipes.
Your devices and product list ought to make up the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your installment, then the first thing you must do is separate the water supply. After doing so, switch on the faucets to drain pipes any water staying in the system. The procedure of getting rid of the existing taps can be rather troublesome due to the restricted gain access to that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that links the supply pipelines to the faucets. Have a towel all set for the continuing to be water that will come from the pipes. Once the supply pipes have been gotten rid of, make use of the same device to loosen the nut that holds the taps onto the bath/basin. You will need to stop the single taps from turning during this process. Once the taps have been removed, the holes in the bath/basin will need to be cleansed of any kind of old securing substance.
Prior to going on to fit the brand-new taps, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new taps to fit.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damage to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will require lowering couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, position the faucet in the placing hole in the bath/basin guaranteeing that the washers are in area in between the faucet as well as the sink. Secure the faucet in position with the producer provided backnut. Once the faucet is safely in place, the supply pipelines can be linked to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The former type should be attached to the faucet finishes first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Tub
Making use of both wooden boards under its feet, place the bath tub in the needed setting. The wooden boards are handy in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 little points.
The following goal is to guarantee that the bath tub is leveled all round. This can be attained by inspecting the spirit level as well as adjusting the feet on the bath tub up until the spirit level reviews level.
To install faucets, fit the bottom of the furthest adaptable tap adapter to the proper supply pipe by making a compression sign up with; then do the very same for the other tap.
Activate the supply of water as well as examine all joints and brand-new pipework for leakages and tighten them if needed. Fill the tub as well as also examine the overflow outlet and also the typical electrical outlet for leaks.
Lastly, fix the bathroom paneling as defined in the producer's user's manual. Tiling and securing around the bathtub ought to wait till the bathtub has been utilized at the very least once as this will resolve it right into its final position.
Getting ready for the Installment
To start with, the supporting framework provided with the bathroom ought to be fitted (if called for) according to the producer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is very important to see to it that if the tap includes a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the taps unit to avoid pressure on the bathtub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts as well as olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet through the hole in the bath. Utilize the nut provided by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make certain you make use of every one of the provided washers.
Connect the trap to the bottom of the waste outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom need to currently prepare to be suited its last position.
Tiling Around the Bathtub
In the area where the bath meets the tile, it is necessary to seal the joins with a silicone rubber caulking. This is important as the fitting can move enough to crack a rigid seal, causing the water to penetrate the wall between the bathroom and also the tiling, bring about difficulties with wetness and also feasible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and also installations. They are marketed in tubes as well as cartridges, as well as are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly fill up the bathtub with water prior to securing, to enable the motion experienced when the tub is in usage. The sealant can break fairly very early if you do not think about this motion before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally quickly available on the market. It is suggested to fit the ceramic tiles using water-resistant or water-proof adhesive and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I recently found that entry about Tools You Need to Install a New Bathtub when scouting around the web. Do you know anybody else who is involved in the topic? Do not hesitate to share it. Many thanks for your time. Come back soon.
Get Offer